VOOPOO Drag S2 60W Pod System
The Drag S2 is the internal-battery half of the Drag S2 and X2 pair. Same Gene.TT board, same 5ml PnP X pod, but a 2500mAh cell built in, so there is nothing to buy or swap. Output tops out at 60W. Fire button, TFT screen, and a zinc alloy shell that has some weight to it.
- 5-60W adjustable, resistance range 0.1ohm to 3.0ohm
- 2500mAh internal battery, USB Type-C charging
- 5ml PnP X side-fill pod with an 810 drip tip
- SMART mode reads coil resistance and sets the wattage
- Zinc alloy body, magnetic pod connection, PCTG pod tank
- Ships with a 0.2ohm and a 0.3ohm PnP-X coil
Drag S2 Specs
| Spec | Detail |
|---|---|
| Wattage | 5-60W, adjustable |
| Battery | 2500mAh internal, non-removable |
| Charging | USB Type-C |
| Voltage | 3.2-4.2V |
| Resistance range | 0.1ohm to 3.0ohm |
| Pod capacity | 5ml PnP X, side fill |
| Chipset | Gene.TT |
| Display | TFT colour screen |
| Operation | Fire button |
| Body | Zinc alloy, magnetic pod connection, PCTG pod |
| Drip tip | 810 |
Coils and Pods That Fit
| Part | What you get | Notes |
|---|---|---|
| PnP-X coils | 0.15ohm to 1.0ohm, seven builds | Press-fit into the pod, no threading |
| PnP-X cartridge pods | Empty DTL or MTL pod, 5ml | Takes any PnP-X coil, coils sold separately |
| PnP-X Tank | Empty tank, 5ml, 510 threaded | MTL or DTL version, for 510 mods |
Which Resistance to Start With
| Coil | Wattage | Best For |
|---|---|---|
| 0.15ohm mesh | 50-60W (device max) | Direct lung, freebase |
| 0.2ohm mesh | 40-60W | Direct lung, freebase |
| 0.3ohm mesh | 32-40W | Direct lung to restricted direct lung |
| 0.45ohm | 25-32W | Restricted direct lung |
| 0.6ohm | 18-23W | Tighter draw, salt or freebase |
| 0.8ohm | 12-16W | Mouth to lung, nic salt |
| 1.0ohm MTL | 10-13W | Tightest draw, nic salt |
The 0.15ohm coil is rated to 80W on paper. The Drag S2 caps at 60W, so it runs at the bottom of that coil's range here. If you want the full 80W on the same coils, that is the Drag X2 or Drag X3.
In the Box
- Drag S2 device
- PnP X DTL cartridge, 5ml
- 1x 0.2ohm PnP-X coil
- 1x 0.3ohm PnP-X coil
- Type-C cable
- User manual
Why Shop VOOPOO at Central Vapors
We stock every PnP-X resistance from the 0.15ohm mesh through the 1.0ohm MTL build, plus spare PnP-X cartridge pods and the PnP-X Tank, so a replacement is a reorder instead of a hunt. Central Vapors has been filling vape orders since 2013, and every order is backed by our satisfaction guarantee.
Common Questions
| Q |
Does the Drag S2 need a separate battery?
No. The 2500mAh cell is built in and charges over Type-C. The Drag X2 is the external-battery version of the same device if you would rather swap cells.
|
| Q |
Which coils fit?
The PnP-X range, 0.15ohm through 1.0ohm MTL. They press-fit into the pod. Older PnP coils do not fit the PnP-X pod.
|
| Q |
Can I use it for nic salt?
Yes. Put in a 0.8ohm or 1.0ohm MTL coil and run it around 10-16W. The coils in the box are sub-ohm and suited to freebase e-liquid at higher wattage.
|
| Q |
How do I refill the pod?
It fills from the side. Pull the pod off the magnets, open the silicone plug, fill, and drop it back on.
|
| Q |
What is SMART mode doing?
Reading the resistance of whichever coil you installed and setting a wattage that suits it. You can override it and set the wattage yourself.
|
| Q |
Is 60W enough for direct lung?
Yes, comfortably. The 0.2ohm and 0.3ohm coils both sit inside 60W, and those are the two builds most people run for direct lung on this device.
|
For use by adults 21+.
